Factory presets are how most of us discover MPE. Load a well-programmed pad, press into a chord, and it comes alive. But sooner or later, you want a sound that responds exactly the way you play. The best way to get there is to start from a blank, or "init", patch and build the expression yourself.
This guide uses a method that works in nearly any MPE-capable synth. Free options such as Surge XT and Vital are ideal for practice, but the same steps apply to commercial instruments.
Step 1: Check the plumbing first
Before touching a single oscillator, confirm that MPE data arrives correctly:
- MPE mode is on in the synth, and the DAW track is set to pass MPE (not merge channels).
- Pitch-bend range matches your controller. Most controllers use ±48 semitones per note. If the synth uses ±2, a small slide becomes a tiny bend and your tuning will feel wrong.
- Polyphony is high enough. Each note needs its own voice, so set at least 8 voices.
Play a single note and slide your finger sideways. If the pitch follows smoothly and returns to centre, the foundations are right. The MIDI Association's MPE overview is a useful reference if anything looks odd.
Step 2: Make a simple, neutral sound
Start with one sawtooth oscillator into a low-pass filter. Set the amp envelope with a short attack, full sustain and a medium release. Leave effects off for now.
The goal is a sound that is plain but responsive. Rich presets can hide what each MPE dimension is doing. A plain saw shows you every change clearly.
Step 3: Assign pressure (Z) to loudness and brightness
Pressure is the most important dimension, so give it two jobs:
- Pressure to amplitude. Map it to a VCA or volume modulation with a moderate amount. Now notes swell when you press.
- Pressure to filter cutoff. Add a second routing to the cutoff, with the base cutoff set fairly low.
Play a sustained chord and press each finger at a different strength. You should hear each note get louder and brighter independently. This is the core of MPE.
Tip: if the sound jumps too quickly, use a softer pressure curve in your controller's software, or add a little smoothing on the modulation in the synth.
Step 4: Assign slide (Y) to timbre
Slide, also called timbre or CC74, is the forward-and-back movement on most controllers. It works best on a different kind of change from pressure, so you can control them separately. Good targets:
- Filter resonance for a vocal, wah-like quality
- Oscillator shape or wavetable position for a change in character
- A second oscillator's level to blend in another tone
Avoid mapping slide to cutoff if pressure already controls it. Two dimensions on one target make the sound harder to play.
Step 5: Shape the release and strike
Now refine how notes begin and end:
- Strike velocity can drive the attack time or initial filter amount, so hard hits sound sharper.
- Release (lift) velocity, if your controller sends it, can set the release time. A slow lift gives a long tail, a quick lift stops the note.
These details make a patch feel like an instrument rather than a sound.
Step 6: Add movement carefully
Per-note vibrato comes from your finger, so you rarely need an LFO on pitch. Instead, try an LFO on filter or pan with its depth controlled by pressure. Light touch gives a still note. Heavier pressure adds motion.
Then add effects: a chorus for width, and a reverb. Keep effects light until you are happy with the dry response.
Step 7: Test like a performer
Play your patch the way you would on stage:
- Long chords with independent pressure per note
- Fast lines to check the envelopes are not too slow
- Slides between notes to check pitch tracking
- Very light playing to make sure soft notes are still audible
Adjust modulation amounts until the full range of your touch produces a musical result, not just the extremes.
Save versions as you go
Save a copy after each step: "Init + pressure", "Init + pressure + slide", and so on. This gives you templates for future patches and makes it easy to compare. Over time, you will build your own library of expressive starting points that suit your controller and your playing style.
For more on each dimension, see our other MPE guides and tutorials.