In October we wrote about early demo videos of a multi-touch MPE terminal from GMXE, which drove four analog oscillators through polyphonic CV (our first report is here). The instrument has since appeared in public at the Beijing Modular event. A SonicState report from the show adds new details on price, modules and timing. It also clarifies one technical point that changes how you would play it.

A note on naming: the demo videos on MATRIXSYNTH use the name YOLA, while SonicState's show report uses YOLO. They appear to describe the same GMXE instrument. We will use YOLA here, and update if the maker confirms a final name.

What was shown in Beijing

According to SonicState, YOLA is a modular MPE controller system built around a desktop control unit. You attach interchangeable modules to it:

The modules use a pin-out connection, and a cable setup for up to five modules is planned. On the software side, YOLA sends MPE over MIDI, and Ableton Live was named as a target.

The touch surface is capacitive multi-touch, supporting more than eight fingers moving in several directions.

Price and timing

SonicState gives approximate figures, so treat these as guidance rather than final pricing:

The official site is gmxe.org. Check there for final specifications before you plan a purchase.

The pressure question

Here is the detail worth slowing down for. The SonicState report states that the controller has no pressure sensing. Our October article, based on early descriptions, mentioned pressure among YOLA's dimensions. The newer show report is more specific, so we are flagging it. Until GMXE publishes a full specification, assume that touch position and movement are the main expressive dimensions.

Does that make it "less MPE"? Not necessarily. MPE is a transport format, defined by the MIDI Association. It gives every note its own channel so that pitch bend, CC74 (slide) and channel pressure can be sent per note. A controller does not have to use all three. Several well-known touch surfaces work mainly with position, and players get very expressive results from them.

But it does change how you set up sounds.

Playing and patching a touch-only MPE surface

Most MPE presets assume pressure is the main source of dynamics. A pad that swells as you press or a lead that brightens under force is the typical design. On a surface without pressure, those patches can sound flat, or they can stay at a fixed level. Some practical adjustments:

1. Move dynamics to strike velocity or slide. If the controller sends a meaningful velocity value, use it to set the initial level. Then map the Y-axis (CC74) to the parameter that would normally follow pressure, such as filter cutoff or amplitude.

2. Use X-axis movement for vibrato and glides. Horizontal finger movement usually becomes per-note pitch bend. Match the synth's bend range to the controller's setting, often 48 semitones in MPE. If they do not match, your slides will land out of tune. Our guide to pitch rounding on continuous surfaces explains this in detail.

3. Let lift and release time do the shaping. Without pressure, the moment you lift a finger becomes an important gesture. Longer, velocity-sensitive release envelopes help notes end musically.

4. On the CV side, patch position into VCAs and filters. With a polyphonic CV module, each voice gets its own pitch and gate, as shown in the earlier demos. If the module also outputs per-voice position as CV, it can do the job that pressure CV does in a classic setup. We cover the general approach in MPE to CV for polyphonic modular.

Where it fits

Multi-touch surfaces without pressure have an appeal of their own. They often feel fast and light, and they reward sliding and gliding more than digging in. Players coming from keyboards with aftertouch may need some time to adjust. Players coming from touchscreens, or from instruments like the Embodme Erae and Sensel Morph, may feel at home quickly.

What makes YOLA unusual is the modular approach. One surface can become a MIDI controller, a self-contained synth, a sequencer or a polyphonic CV source, depending on which modules you attach. For musicians who move between a DAW and a modular case, that flexibility could be the main selling point.

We will follow up when GMXE publishes final specifications, including whether any form of pressure sensing makes it into the shipping version.