MPE is a protocol, not a playing technique. The specification defines how per-note pitch bend, pressure and the CC74 "slide" or "timbre" dimension travel between devices. It says nothing about how your fingers produce that data. That is why a patch that feels perfect on one controller can feel twitchy or lifeless on another.

This week's announcement of Exquis+, which senses two-axis tilt on each key, is a good moment to look at the two main families of sensing: position-based and tilt-based. Understanding the difference will help you choose a controller and set up your sounds properly.

Position-based sensing: where your finger is

On many controllers, the Y-axis value depends on where your finger sits on a key or surface. Move forward, and the value rises. Move back, and it falls.

The ROLI Seaboard is the classic example: you slide your finger along the soft keywave to change CC74. The LinnStrument reads finger position within each pad. The Haken Continuum tracks X, Y and Z continuously across its playing surface.

Strengths: large, readable gestures. You can see where your finger is, and the full range is spread over a few centimetres, which gives fine control.

Things to watch: the initial value depends on where you land. If you strike near the front edge, your note starts with a low CC74. That is why many controllers offer a relative Y mode, where the starting position counts as zero and only movement changes the value. If your filter sweeps sound inconsistent from note to note, check this setting first.

Tilt-based sensing: how you lean

Other designs measure the angle or force direction of your finger on a key, rather than its position. You rock the finger forward or sideways, and the key reports that lean as a continuous value. Exquis uses this approach, with tilt on two axes.

Strengths: gestures are small and fast, which suits dense chord playing and compact layouts. Each note normally starts from a neutral centre, so you avoid the "where did I land?" problem.

Things to watch: the physical range is short. A patch that maps CC74 to a wide filter sweep can feel abrupt, because a tiny lean covers the whole range. Tilt also tends to mix slightly with pressure, since leaning a finger changes how hard you press.

Tuning a patch for each family

The good news is that most problems are fixed in the synth, not the controller. These adjustments work in any MPE-capable instrument, from Arturia Pigments to Bitwig's built-in devices.

1. Scale the modulation depth. For tilt-based controllers, start with about half the CC74 depth you would use on a Seaboard. For position-based surfaces with a long throw, you can usually go deeper.

2. Add a curve or smoothing. A gentle exponential curve on CC74 makes small movements more subtle while keeping the top of the range. A few milliseconds of smoothing hides jitter, which is more noticeable on short-throw sensors.

3. Choose a sensible centre. If your controller sends neutral at 64, use a bipolar modulation so leaning forward opens the filter and leaning back closes it. If it sends 0 at rest, use a unipolar setting. Mixing these up is a common cause of patches that sound dull until you move.

4. Separate pressure from timbre. On tilt-based keys, avoid mapping pressure and CC74 to the same parameter at full depth. Give each a distinct job, for example pressure to amplitude and CC74 to brightness.

5. Check the pitch axis separately. Sideways movement for pitch also differs between designs. Make sure the pitch bend range in your synth matches your controller, typically ±48 semitones for MPE. Our explainer on pitch rounding on continuous surfaces covers this in more depth.

Use controller presets, then adjust

Many manufacturers now ship plugin-specific presets that apply these settings for you. The new Exquis app 3.1.0, for example, includes close to 3,000 factory presets for different instruments. Presets like these are a good starting point, but treat them as a baseline. Your hand, your playing style and your music will need small changes.

The takeaway

There is no "correct" way to sense expression. Position-based surfaces offer wide, visible gestures. Tilt-based keys offer speed and a consistent starting point. If a sound feels wrong on your controller, the solution is usually a few minutes of depth, curve and polarity adjustments rather than a new instrument.

For more on the full range of gestures, read our guide to the five dimensions of touch.